Bixby Energy MaxFire Betriebsanleitung

Installation, Operating and MaintenanceInstructionsMaxFireTM Multi-Fuel Room HeaterWARNING! Please read this entire manual before installation and u

82020866 REV ALEVELING THE ROOM HEATERCAUTION: THE ROOM HEATER SHOULD BE LEVELED BEFORE ATTACHING THE VENT PIPE. The supplied bulls eye level can b

92020866 REV AVENT SYSTEM APPROVALSBIXBY DIRECT VENT PIPE is listed by OMNI-Test Laboratories, Inc. as a vent for BIXBY pellet and corn Room Heaters o

102020866 REV AVENTING COMPONENTSINSPECTIONSThe use of pelletized fuel does not eliminate the need for inspection and cleaning. During the heating sea

112020866 REV AVENT LOCATIONWhen exiting through walls, make sure NFPA rules are followed for distance from windows and openings. NOTE:The termination

122020866 REV AVENT LOCATION (CONT.)Where passage through a wall, or partition of combustible construction is desired, the installation shall conform

132020866 REV AVENTING CONFIGURATIONSThe allowable venting configuration is to be 25 equivalent horizontal feet (7.5 m) or less as determined through t

142020866 REV AGENERAL VENT INSTALLATION INSTRUCTIONSFollow the Room Heater manufacturer’s instructions and safety manual for maximum efficiency and sa

152020866 REV AVERTICAL INTERIOR INSTALLATIONNOTE: Vertical exterior installation is not recommended due to excessive condensation.NOTE: Bixby recom

162020866 REV AHORIZONTAL THROUGH-THE-WALL-INSTALLATION The flue exit is on back of the Room Heater, and if a horizontal through-the-wall installation

172020866 REV AINSTALLATION IN A CATHEDRAL CEILING1. Mark a line on the side of the Cathedral Ceiling Support Box to correspond to the line

182020866 REV AINSTALLATION IN A CATHEDRAL CEILING (CONT.)8. Place the Vertical Support Clamp (5000576), around the top of the hole in the bottom of

192020866 REV ACONNECTING TO EXISTING CLASS A CHIMNEY EITHER 6” OR 8”Due to cleaning, inspection and condensation issues, Bixby no longer recomends co

202020866 REV ALOG PLACEMENT INSTRUCTIONSThe use of the logs provided with the Room Heater is optional.1. Locate the log box and remov

212020866 REV AFUELIt is strongly recommended that only Dry Shelled Corn (whole kernels), Wood Pellets (recommended maximum size approx

222020866 REV ASTART UPNOTE: It is recommended that all gold or silver plated surfaces of the Bixby Room Heater be cleaned with a mild glass cleaner

232020866 REV AThe 8 heat level indicator lights on the Bixby Room Heater are also designed to act as potential problem indicators. Whenever one of t

242020866 REV AMAINTENANCE AND CLEANING PROCEDURESThe Bixby Room Heater has been designed to reduce the frequency of cleaning. However,

252020866 REV AAsh DrawerFigure 28HEAT EXCHANGER TUBESFly ash and other deposits will accumulate on the Heat Exchanger Tubes over time and will a

262020866 REV ACLEANING THE EXHAUST MANIFOLDThe Exhaust Manifold should be cleared on a yearly basis to ensure proper air flow in the Room Heat

272020866 REV AFUEL HOPPERThe Fuel Hopper should be cleaned out on a regular basis (monthly) to remove fines and ensure proper fuel delivery.

12020866 REV ATABLE OF CONTENTSSafety Information 2Minimum Clearances to Combustible MaterialsSpecifications 4Planning the Installation 6Performing

282020866 REV ACLEANING THE LOWER PADDLEThe Lower Paddle needs to be cleaned once a month in order to operate efficiently. The ash dumping pro

292020866 REV ATROUBLESHOOTING PROCEDURESWhen experiencing a malfunction, please read through the following list of possible problems to determine whi

302020866 REV APROBLEM POSSIBLE CAUSE/REMEDYFire fails to start Be sure enough fuel is in the burn pot. Fuel should cover the bottom to a level of ap

312020866 REV AWIRING DIAGRAMFigure 37MFG APPR.QA APPR.ENG APPR.DRAWN BYDATENAMESHEET 1 OF 1IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF BI

322020866 REV ASERVICE PARTS LISTItem Number Description Part Location4000080 Igniter4000121 Air pump4000113 Burner drive motor assembly4000006 Feeder

332020866 REV AItem Number Description Part Location4000022 Heat exchanger cover plate - RightHeat exchanger cover plate - Left4000048 Air Filter40000

342020866 REV AItem Number Description Part Location4000353 Burner top plate4000361 Feed wheel sensor4000379 Fuel deflector4000329 Thermocouple4000337

352020866 REV ADescription Color / Size Part #Vertical Termination Cap Black 5001368 Wall Thimble Aluminized Steel 5000526 Storm Collar Stainless Stee

362020866 REV ADescription Color / Size Part #6” Straight Pipe Black 5000055Blushtone* 5000063Hunter Green* 500008912” Straight Pipe Black 5000170Burg

372020866 REV ADescription Color / Size Part #Decorative Collar Black 5000740 Blushtone* 5000758Hunter Green* 5000774Sheet Metal Screw Black 5000857Bl

22020866 REV ASAFETY INFORMATION1. Install and use only in accordance with these installation and operating instructions, page 9. Contact local buil

382020866 REV ADate Service Performed NotesMAINTENANCE LOG

32020866 REV AMINIMUM CLEARANCES TO COMBUSTIBLE MATERIALSUse a non-combustible floor protector under the unit, extending 3” (76mm) past the side of un

42020866 REV ASPECIFICATIONSFuel: Multi-fuel System: Dry shelled corn, Wood Pellets (recommended maximum size approximately ¼ in. diameter x 1¼

52020866 REV AIMPORTANT: Proper material handling equipment must be available to safely transport and position the Bixby Room Heater. 1. Remove the

62020866 REV APLANNING THE INSTALLATIONThe Bixby Max-FireTM Room Heater is intended for use in buildings, manufactured homes or for mobile home instal

72020866 REV AFEEDRATE3535- 0 +THERMOSTAT CONNECTION2021781 REV AEXHAUSTFAN- 0 +3535FUELCORN WOOD OPTIONAL THERMOSTAT OPE